What is a custom car audio subwoofer enclosure? Does it need to be wrapped in leather or vinyl? Should it be made with fiberglass? Does it need acrylic windows? Is LED lighting a necessity? The short answer is no to all of these questions. Let’s delve into what makes a subwoofer enclosure custom and why it’s the best way to upgrade the bass in your car audio system.

Subwoofer Enclosure Volume Matters

How large does a subwoofer enclosure need to be? The answer to that depends on the subwoofers you want to use. Thinking that way puts the cart before the horse, though. The best way to design a subwoofer system is to tell the product specialist you’re working with how much space you’re willing to allocate to the enclosure. They can take a series of measurements, do some calculations and suggest a subwoofer or subwoofers to deliver the best performance based on the available air volume. No matter what the manufacturers tell you, cramming large subwoofers into small enclosures results in poor performance. You’ll get more deep bass from a single driver in an optimized enclosure than a bunch of larger drivers crammed into an undersized design.

Part of designating the space available for your subwoofer enclosure should include considerations about accessing storage or a spare tire. The last thing you want is to be stranded on the side of the road because part of your stereo has trapped a spare or blocked access to the vehicle battery. Before you tell the shop how much space they can use, look under the trunk floor to determine what you might need to get to. Make some notes so you can share that information with the shop.

Space Optimization Is Key

The number one factor that defines a custom subwoofer enclosure is that it optimizes the available space in the vehicle. Let’s say you want a vented enclosure with two 10-inch subwoofers. Most 10-inch subwoofers on the market work very well in about 1 cubic foot of air space. So, this enclosure would need a net volume of 2 cubic feet plus the displacement of the drivers and the vent. Let’s use a pair of ARC Audio X2 10D2V2 10-inch subwoofers for this simulation. With 1 cubic foot each, plus a 4-inch diameter round vent, the enclosure needs a net internal air volume of about 2.15 cubic feet.

The person designing the enclosure for these subwoofers should optimize it so that it intrudes into the cargo area of the trunk as little as possible. Therefore, it should use the full width and all the available height to make it as shallow as possible. If we have 40 inches of width and 15 inches of height, the enclosure would need to be 8.625 inches in depth. These measurements assume the enclosure is a rectangle with no angled rear panel. If we wanted the rear panel to have a 20-degree angle, the depth at the top would shrink to about 6 inches. That gives us two more inches of usable cargo space.

Both designs are custom enclosures if finished in a durable carpet that matches the cargo area. That’s it. Nothing fancy or exotic is required to make this a custom solution. The customization aspect is that the enclosure is optimized for your vehicle and uses the available space efficiently.

By contrast, if the shop has a pre-built enclosure that’s 34 inches wide and 13 inches tall, it would need to be 11.375 inches deep. Would it work? Yes. Would it sound the same? Yes. Might it save you money versus having an enclosure built specifically for your application? Maybe. Will you have the most space to fit your groceries, sports equipment, luggage or beer? No, not at all.

Here are a few examples of custom enclosures designed to deliver great bass while taking up as little space as possible.

More Custom Subwoofer Enclosure Options

Now, there is a next level of custom subwoofer enclosure beyond a square or slanted-back prism. You might have a significant amount of room inside a spare tire or behind a trim panel in the trunk that can be used for an enclosure. Once again, the choice of drivers for these applications depends on the available space. Just because you can physically fit a 12-inch subwoofer inside a spare tire enclosure doesn’t mean that’s the choice of driver that will produce the most low-frequency output or deliver the tightest bass. A single 10-inch subwoofer might play louder at lower frequencies. An 8-inch subwoofer in a vented design will likely be even louder. Once again, the shop you’re working with should calculate the available volume and suggest a subwoofer based on that information.

Vehicle-Specific Enclosures

Many companies offer off-the-shelf subwoofer enclosures designed for specific vehicles. These enclosures are typically optimized for a specific location in the vehicle and may use a combination of stack-fab or fiberglass construction. With the benefits of mass production, these custom enclosures can make adding an optimized bass solution more affordable than having a shop create a one-off solution. You’ll still need an expert to run all the wiring and configure and calibrate the electronics.

Net Audio in Wichita Falls, Texas, offers this 2019+ Ram 1500 Crew Cab bass reflex subwoofer solution.

Musicar in Portland, Oregon, offers a variety of BMW OE-Look subwoofer upgrades, including this enclosure for F32/F83 coupes with a Morel 10-inch subwoofer.

Audio Designs and Custom Graphics in Jacksonville, Florida, has a complete line of Phantom Fit enclosures, including this one for 2015-22 Mustangs.

MTI Acoustics in College Station, Texas, offers application-specific subwoofer enclosures like this one for Jeep Gladiators.

Upgrade Your Car Stereo with a Subwoofer System Today

As we’ve shown, there doesn’t need to be anything fancy or exotic about a custom subwoofer enclosure. The enclosure needs to be constructed to be specific to your needs. You can certainly go for something flashy if you want. However, we prefer to stick with a simple, well-constructed enclosure and opt for a subwoofer that includes technologies that make it more accurate and linear. No matter your goal, drop by a local specialty mobile enhancement retailer today to find out what they can build to deliver great bass in your car, truck or SUV.

Lead-In Image: Thanks to Perzan Auto Radio in Upper Darby, Pennsylvania, for the photo of this enclosure they constructed for a client’s 2023 Bentley Continental GT Azure. The enclosure features a pair of JL Audio 10W6v3 subwoofers and matching SGR-10W6v2/v3 grilles. The client can still access the space under the trunk floor without moving the enclosure.

This article is written and produced by the team at www.BestCarAudio.com. Reproduction or use of any kind is prohibited without the express written permission of 1sixty8 media.

Once again, we approach a discussion of the laws of physics and how they affect the electrical systems in our cars and trucks. The enemy of all power transmission systems, be it the battery and alternator to the amplifier in your vehicle or the nuclear power station or hydroelectric dam across the state to your home, is resistance. I saw a power wire sizing chart earlier this week that had me rethink how car audio systems are wired, so I thought we’d take another look.

Ohm’s Law and Wasted Power

Ohm’s Law states that for every amp of current that flows through a resistance of 1 ohm, 1 volt is produced across that resistance. If we lower the current, less voltage is produced. If we reduce the resistance, less voltage is produced. We are typically limited to 14 volts from a fully functional alternator in our cars and trucks. If the wiring between the alternator and the amplifier has resistance (and it does), some of the voltage is wasted across the wire and doesn’t reach the amp. Most aftermarket amplifiers in car audio systems have loosely or completely unregulated power supplies. As such, the amplifiers can produce more power if fed more voltage. Conversely, if we starve them for voltage, the maximum power they can produce decreases.

Power Wiring and Voltage Loss

A member of the Motorsport Wiring Alliance Facebook Group posted the chart below. The folks at WireCare provided him with the chart in response to an inquiry about the conductor’s current carrying limits. What’s unique about this chart is that it considers conductor size based on temperature rather than voltage drop. Why is this important? When a conductor heats up, its resistance increases. The increased resistance produces more heat, which creates even more resistance. It’s easy to see that this can quickly result in a runaway situation.

Now, before we get into a discussion about why choosing the correct wire size is essential, let’s talk about Tefzel wire specifically. If you’re accustomed to the typical wiring used for car audio upgrades, Tefzel is entirely different. This type of wire uses an ethylene tetrafluoroethylene copolymer (ETFE) jacket that can withstand temperatures up to 150 degrees Celsius. The primary power wire most car audio folks use has a PVC jacket and is rated for around 105 degrees Celsius.

It’s worth noting that Tefzel is a brand of ETFE and not specifically a brand of wire. When referring to Tefzel wire, the name describes the type of jacket on the wire. Tefzel is a type of ETFE resin and is sold as a raw plastic material in pellet form. Tefzel is also used in heat-shrink tubing, valve linings and biomedical equipment. Tefzel is a Chemours Co. brand, just like Teflon, Viton and Freon.

Tefzel is the standard for aviation wiring and custom wire harnessing that you’d find on any professional-level race car. A key advantage to Tefzel is that the shielding is very thin and durable, which results in smaller-diameter wire bundles. Further, the ETFE jacket doesn’t contain chlorine, which produces a lot of smoke when it burns – a key consideration in aeronautics applications. The downside is that it’s expensive. But, as they say, you get what you pay for.

A secondary benefit of the thin jacket is the ability of the wire to dissipate heat quickly compared with a conductor with a thick jacket. Allowing heat to escape to the air around the wire helps keep the resistance down, which minimizes voltage losses and improves efficiency. However, if you look at the above chart, the ratings are not directly comparable to typical car audio wiring in dissipating heat.

Let Your Power Wire Be Free!

If you’re feeling particularly geeky, I recommend browsing NASA’s Re-Architecting the NASA Wire Derating Approach for Space Flight Applications document. In short, bunding many wires together can dramatically reduce their ampacity as heat generated in the conductor cannot escape the wire bundle easily. If you have a bunch of wires zip-tied together, they could present more resistance and consequently waste more energy than if each were out in the open with nothing touching them. From their research, a single 26 AWG conductor in free space could handle up to 4.7 amps of current and not exceed 200 degrees. When that same conductor was at the core of a bundle of 32 other wires, the maximum allowable current was 1.9 amps to reach a similar temperature. What’s the takeaway? Routing wiring away from heat sources will dramatically improve its current carrying performance.

This chart shows how the current handling capability of wiring decreases as more and more conductors are bundled together.

Power Wire and Heat Calculations

It’s common practice to consider all-copper 4 AWG power wire suitable to deliver up to 100 amps of current to an amplifier. Assuming the wire meets the ANSI/CTA-2015 Mobile Electronics Cabling Standard, 1 meter of 4 AWG should have no more than 0.88 milliohm of resistance. Assuming we usually need about 4.5 meters of wire to run from the battery to an amplifier in the trunk, we’d have a drop of 0.396 volt across the wire when 100 amps pass through it. Assuming the ground path has a similar resistance, that’s another 0.396-ish volt of drop. So we’ve lost about 0.8 volt from whatever the alternator produced.

I’ve measured dozens of copper-clad aluminum amp kits over the years. The best of those kits had a resistance of 1.43 milliohms per meter, and the worst I’ve tested had 3.37 milliohms per meter. So if we attempt to draw the same amount of current through those conductors, we have a voltage drop of 0.6435 and 1.517 volts, respectively. Add the drop of the return path, and you have a total of just over a volt and almost 2 volts for the dramatically undersized 4 gauge CCA wire.

The Tefzel wire chart describes an appropriate wire size for a given operating temperature range. In the case of their 4 AWG wire, their wire has an even lower resistance of 0.816 milliohm per meter. Drawing 100 amps through 4.5 meters of their wire results in a voltage drop of 0.367 volt. Honestly, that’s not worth the added cost. It’s also not the point of this discussion.

Tefzel rates the ampacity of their wire based on its operating temperature. According to their chart, 72 amps of current through Tefzel 4 AWG will raise the wire temperature by 35 degrees. Some simple math tells us that the wire dissipates 4.23 watts of energy per meter at that current level. For the maximum temperature to increase by only 10 degrees, they state that 40 amps is the maximum, which is 1.31 watts per meter. If we reverse the math, a 4 AWG car-audio-style all-copper power wire is only suitable for 38.55 amps of current to produce a temperature increase of 10 degrees. If we accept the 35-degree temperature increase, we max out at 69.35 amps. What about the CCA wire? The “good” CCA wire could pass 54.4 amps of current for the 35-degree rating, and the woefully undersized CCA is only good for 35.45 amps.

The issue with exceeding the ampacity rating of the wire is that it heats up. Pure copper has a temperature resistance coefficient of 0.00393. This means that for every increase in temperature of 1 degree Celsius, the resistance of the wire goes up by 0.393%.

As you can see, the effect of a conductor getting hot can dramatically increase its resistance. For example, at 100 degrees C, 4 AWG has more resistance than a conductor with an equivalent size to 5 AWG at 20 degrees.

Thankfully, we play music, not test tones, through our audio systems. Because of the dynamic nature of music, we get an averaging effect that dramatically reduces the power an amplifier needs to produce. Assuming you aren’t playing basshead music, it wouldn’t be unreasonable to consider that the average amplitude of a rock track would be about 12 dB, which equates to a 16x reduction in required power. In the context of our wire size discussion, if the maximum current your amp would draw is 100 amps, the average might be down to around 6.25 amps. Of course, there are a LOT of variables in that statement, but even if the average is 25 amps, you have a significant safety margin.

Don’t Starve Your Car Audio Amplifier

The first takeaway is that 2 AWG power wire needs to be much more prevalent in car audio applications. For example, a 1,500-watt amplifier that’s reasonably efficient would work well with 2 AWG wire.

Secondly, if you want your amplifier to produce all the power it claims, you must choose a high-quality power wire large enough for your application. The average power produced by an amplifier might be well below the maximum ratings, but that doesn’t mean you might still be limited when the peaks happen. Don’t skimp on power wire size or quality. A great way to add some reserve energy is to have the technician working on your car install a high-quality stiffening capacitor near the amplifier. Consult with a local specialty mobile enhancement retailer when choosing the correct power wire for the installation they’re performing.

This article is written and produced by the team at www.BestCarAudio.com. Reproduction or use of any kind is prohibited without the express written permission of 1sixty8 media.

In the fall of 1982, Billy Joel’s 52nd Street was among the first 50 albums released as consumer-available compact discs. It had been only about four years since digital recording equipment was introduced to studios. This marked a revolutionary change in how consumers would buy their music. It was the dawn of an all-digital era, where performers could have their music captured with impressive accuracy and minimal background noise for delivery to consumers. Since then, not much has changed in the way we digitally capture and store analog waveforms. We just have a few more bits of depth to improve noise performance and higher sampling rates to ensure that bats and mice can hear that extra octave.

On the reproduction side of things, dozens of companies have made claims about increases in performance because of these higher sampling rates and increased bit depth. Unfortunately, the marketing guys haven’t been talking to the engineers to understand how the process works. This article will look at the digital stairstep analogy and explain why it’s misleading.

How Is Analog Audio Sampled?

Digital audio sampling is a relatively simple process. An analog-to-digital converter (ADC) measures the voltage of a waveform at a specific rate and outputs digital information that represents those amplitudes. The sampling rate defines the number of samples per second, determining the Nyquist frequency. The Nyquist frequency is the highest frequency the ADC can record accurately and is half the sample rate. For a compact disc with a sampling rate of 44.1 kHz, the highest frequency is 22.05 kHz. This frequency is beyond what most humans can hear, so it’s more than high enough to capture any audio signal we’d need to reproduce.

Bit depth describes the number of discrete amplitudes captured in a sampling process. If you have read audio brochures or looked at websites, you’ve undoubtedly seen a drawing showing several cubes intended to represent samples of an analog waveform. These diagrams are often referred to as stairstep drawings.

The size of the blocks on the horizontal scale represents the sampling rate, and the size on the vertical scale is the bit depth. We have 20 levels in this simulation, equating just over 4.3 bits of resolution. It’s not difficult to see that this would introduce some amount of error and unwanted noise. However, even the earliest digital samplers, like the Fairlight CMI, had only 8 bits of depth, equating 256 possible amplitudes. Later versions increased the bit depth to 16, dramatically improving sample accuracy.

Once we have enough bit depth, we can accurately reproduce the waveform without adding unwanted noise. For example, the orange data in the image below has lots of bit depth, and the difference between the orange and blue would be perceived as noise in the recording.

What about those steps? Isn’t music supposed to be a smooth analog waveform and not a bunch of steps? Companies that purport to offer support for higher resolution audio files or those with more bit depth will often put a second image beside the first with smaller blocks. The intention is to describe their device as being more accurate.

The problem is, the digital-to-analog converter doesn’t reproduce blocks. Instead, it defines an amplitude at a specific time point. A better representation of how analog waveforms are stored would be with each amplitude represented by an infinitely thin vertical line.

A better way to describe the function of a DAC is to state that each sample has a specific voltage at a particular point in time. The DAC has a low-pass filter on its output that ensures that the waveform flows smoothly to the next sample level. There are no steps or notches, ever.

Digital Bit Depth Experiment

Rather than ramble on about theory, let’s fire up Adobe Audition and do a real-world experiment to show the difference between 16- and 24-bit recordings. We’ll use the standard compact disc sampling rate of 44.1 kHz and a 1-kHz tone. I created a 24-bit track first and saved it to my computer. I then saved that file again with a bit depth of 16 bits to ensure that the timing between the two would be perfect.

Here’s what the waveform looks like. The little dots are the samples.

Now, I’ll load both files and subtract the 16-bit waveform from the 24-bit. The difference will show us the error caused by the difference in bit depth.

At a glance, it appears the difference is invisible. Maybe it’s hard to see the difference between the two files. Let’s look at some data in a different format. Here’s the spectral response graph of the difference.

As you can see, the difference is noise at a level of -130 dB. This amplitude is WAY below the limits of any audio equipment and, as such, is inaudible.

Let’s make the comparison more dramatic, shall we? I’ve saved the 16-bit track again with a depth of 8 bits.

This time, we got a result. You can see some waviness in the difference. This makes sense, as an 8-bit file only has 256 possible amplitude levels, and a 1-volt waveform has a possible error of almost 2 millivolts. Let’s look at this in the spectral domain.

Now we have something audible. Not only can we see the 1-kHz waveform in the difference file at an amplitude of -70 dB, but we can see harmonics of that frequency at 1-kHz spacings to the upper limits of the file.

High-Resolution Audio Sounds Better

What have we learned about digital audio storage? First, each sample is infinitely small in the time domain and represents a level rather than a block. Second, there is no audible difference between a 16-bit and a 24-bit audio file. Third, 8 bits aren’t enough to accurately capture an analog waveform. What’s our takeaway? If we see marketing material that contends that a recording format with more than 16 bits of depth dramatically improves audio quality, we know it’s hogwash.

Wait, what about hi-res audio? Doesn’t it sound better than conventional CD quality? The answer is often yes. The reason isn’t mathematical, though. Sampling rates above the CD standard of 44.1 kHz can capture more harmonic information. Is this audible? Unlikely. Does having more than 16 bits of depth help? We’ve proven it doesn’t. So, why do hi-res recordings often sound better than older CD-quality recordings? The equipment used in the studio to convert the analog waveform from a microphone is likely decades newer and adds less distortion to the signal. If the recording is genuinely intended to be high-resolution, the quality of the microphone itself is better. Those are HUGE in terms of quality and accuracy.

A second benefit of higher bit-depth audio files is less background noise. When multiple sound samples are combined in software like Pro Tools, the chances of the background noise combining to become an issue are dramatically reduced.

The next time you shop for a car radio, consider a unit that supports playback of hi-res audio files. They sound better and will improve your listening experience. A local specialty mobile enhancement retailer can help you pick a radio that suits your needs and is easy to use.

This article is written and produced by the team at www.BestCarAudio.com. Reproduction or use of any kind is prohibited without the express written permission of 1sixty8 media.